DISCOVERING ESSENTIAL PLUMBING SKILLS IS ESSENTIAL FOR INSTALLING A BATHTUB

Discovering Essential Plumbing Skills is Essential for Installing a Bathtub

Discovering Essential Plumbing Skills is Essential for Installing a Bathtub

Blog Article

Call

What're your thoughts regarding A Step-by-Step Guide to Installing a Bathtub?


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround
Installing a bath tub isn't specifically rocket science, yet it does need strong plumbing, woodworking, as well as in some cases, tiling skills. Changing an old bath tub with a brand-new one is likewise a reasonably difficult job. If the old bathtub is readily accessible, the project can relocate easily; if you have to open a wall to eliminate the old bathtub as well as position the brand-new bath tub, the task is a lot harder. In either instance, the job is within a house handyman's skills, although you will certainly need a helper to vacate the old tub and set in the brand-new one. Make certain you have certified yourself for the work and also are comfortable attempting it. As opposed to hiring a specialist to take over a halfway-completed job, it is better to consider utilizing one prior to you start. Possibilities are you might need a professional plumber to make tube connections.
This post will certainly assist you set up a brand-new bathtub in your washroom if you have already gotten a new bathtub as well as do not need to change the setup of your previous water pipes.
Your devices and product list must comprise the following:
  • New Bath tub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Knife

  • Tape Measure

  • Pipeline Caps


  • Preparing for the Installment


    First of all, the sustaining frame provided with the bath ought to be fitted (if called for) according to the manufacturer's guidelines. Next, fit the taps or mixer to the tub. When suitable the tap block, it is very important to ensure that if the tap includes a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the faucets unit to stop stress on the tub.
    Fit the flexible tap adapters to the bottom of both taps using 2 nuts and also olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet with the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you utilize all of the provided washing machines.
    Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bathroom must now prepare to be suited its final position.

    Removing Old Touches


    If you require to replace old faucets with new ones as a part of your installment, after that the first thing you ought to do is disconnect the water. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The process of removing the existing faucets can be fairly bothersome as a result of the limited access that is often the case.
    Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the taps. Have a towel all set for the staying water that will certainly come from the pipes. As soon as the supply pipes have actually been gotten rid of, utilize the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from turning throughout this process. When the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleaned up of any type of old securing compound.
    Before moving on to fit the brand-new taps, compare the pipeline links on the old taps to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the brand-new faucets to fit.

    Setting up the Tub


    Making use of the two wood boards under its feet, position the bathtub in the required position. The wood boards are useful in uniformly spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto four little points.
    The following goal is to ensure that the tub is leveled all round. This can be achieved by checking the spirit level as well as readjusting the feet on the bath tub until the spirit level checks out level.
    To set up faucets, fit all-time low of the outermost flexible tap connector to the appropriate supply pipe by making a compression join; then do the exact same for the various other faucet.
    Turn on the water system as well as check all joints and new pipework for leakages as well as tighten them if needed. Load the tub and likewise inspect the overflow outlet and the regular outlet for leakages.
    Ultimately, repair the bathroom paneling as explained in the producer's instruction manual. Tiling and also securing around the tub should wait up until the bathtub has actually been used a minimum of when as this will certainly resolve it right into its last placement.

    Fitting New Taps


    If the tails of the new faucets are plastic, after that you will certainly require a plastic port to avoid damage to the thread. One end of the connector fits on the plastic tail of the tap and the other end offers a connection to the current supply pipes.
    If you need to fit a monobloc, then you will certainly require lowering couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipe.
    Next off, position the faucet in the mounting opening in the bath/basin guaranteeing that the washers are in location between the faucet as well as the sink. Protect the tap in place with the manufacturer offered backnut. As soon as the faucet is safely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with typical faucet ports. The previous kind must be attached to the tap finishes first, tightening up just by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.

    Tiling Around the Tub


    In the area where the bath fulfills the ceramic tile, it is essential to secure the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to split a rigid seal, triggering the water to penetrate the wall between the bath as well as the tiling, causing issues with dampness as well as feasible leakages to the ceiling listed below.
    You can pick from a selection of coloured sealants to blend in your fixtures and also fittings. They are marketed in tubes and also cartridges, and can securing gaps up to a size of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked paper or soft rope. Keep in mind to always load the tub with water prior to securing, to permit the movement experienced when the tub is in use. The sealant can break fairly early if you do not take into consideration this motion before sealing.
    Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also conveniently available on the market. It is suggested to fit the tiles using water-resistant or water-proof glue and cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    How to Install a Bathtub

    As a serious reader on Installing A Bathtub, I assumed sharing that excerpt was worthwhile. You should take a moment to promote this entry if you enjoyed it. We love reading our article about Tools You Need to Install a New Bathtub .


    Free Estimates

    Report this page